What Size Warping Board Do I Need
Wind Warp
This mail service has been updated and moved to:
From the previous example, or from your project plan calculations, you will have
determined that you will need to prepare a warp of 390 ends, each 3.5 yards in length.
Special tools have been created that volition help you to do this – Warping Boards and Warping Mills. If yous don't have
admission to a warping lath or mill, you lot tin thread your yarn by wrapping it around
anything that is the correct distance apart, such as the backs of 2 chairs, making sure
that you create a cross in the yarn with each revolution.
Warping Board
Warping Boards are mostly used for projects up to 13 yards in length. Longer warps
require a Warping Manufacturing plant. On a Warping lath, the distance betwixt each peg is generally one
g. If your project is shorter than 12 yards, it is usually easier to thread your warp
using the full length of the board.
This photo shows a 5 yard warp length.
The example given to a higher place required a 3.5 yard warp length. I usually round upward i/ii yards to
the nearest thousand (if I have sufficient yarn) i.eastward. 4 yards. To begin warping, I tie the
yarn to the first peg on the height Right side of the warping board. Going Left, I run the
yarn Over the commencement peg and Under the post-obit peg, so Over the far Left peg and
reverse direction. Then to the next peg on the Right side of the board, reverse direction
and on to the adjacent peg on the Left side of the lath and and then on until there is a length of
iv yards on the warping board.
Then contrary direction and work your fashion dorsum up to the height of the warping board. At the
tiptop, go over the Left peg, Over the next one, Nether the following and back to the Far
Correct peg. This creates a Cantankerous in the warp
chain. The Cross is very important, equally it keeps the warp yarns in the order that you lot
threaded them.
Warp Bondage
In the higher up example, you would echo this procedure until you take 390 ends. A warping
board doesn't by and large concur 390 ends, so yous will need make several warp chains. I
usually exercise chains of 50 – 100 ends depending on the thickness of the yarn.
Counter Thread
To go along rails of the number of ends that I have wound onto the lath, I use a counting
thread; a contrasting piece of yarn and lace the ends in groups of ten.
Go on Fifty-fifty Tension
As y'all are winding the warp, you might find that the tension on the warp may tend to become
tighter. If this is occurring, yous will notice that the pegs are drawing in. For this
reason, many warping boards do not have the pegs glued in. If the warp is tightening too
much, the pegs volition come loose rather than breaking on you. Try to go along an even tension
while winding on. Otherwise, as the tension increases, each successive warp finish is
shortening and you will end up with a warp of unlike lengths.
Warping Board Plans
How to make a warping board.
Stride 1. Cull your project and yarns.
Footstep 2. Determine the sett of your cloth, or how many threads per inch the cloth will be.
Step 3. Choose the correct Reed
Step iv. Summate the Yarn requirements.
Step five. Current of air the Warp using a warping lath or warping manufactory.
Stride six. Remove the warp chains and place them on the loom.
Step 7. Sley the Reed.
Stride 8. Thread the heddles, post-obit the typhoon plan.
Step 9. Wind the warp onto the back beam
Step 10. Tie the warp ends to the front beam.
Congratulations! Now y'all a ready to Weave!
AMAZON – Hand Weaving Books
Weaving on a Little Loom (Everything you need to know to become started with weaving, includes five simple projects
The Key to Weaving: A Textbook of Hand Weaving for the Get-go Weaver
The Weaver's Companion (The Companion Series)
Learning to Weave
The Large Volume of Weaving: Handweaving in the Swedish Tradition: Techniques, Patterns, Designs and Materials
The Handweaver'due south Pattern Directory
A Weaver's Volume of 8-Shaft Patterns: From the Friends of Handwoven
Krokbragd: How to Pattern & Weave
Doubleweave: On Four to Eight Shafts
Double Weave: Theory and Practice<
Magic of Doubleweave: The Best of Weaver'southward (Best of Weaver's series)
Weaving In the Arts: Widening the Learning Circle
DIY Woven Art: Inspiration and Instruction for Handmade Wall Hangings, Rugs, Pillows and More!
>On the Loom: A Modern Weaver's Guide
EBAY – Used Weaving Looms
BAND WEAVING
RIGID HEDDLE LOOMS
USED Flooring LOOMS
What Size Warping Board Do I Need,
Source: https://allfiberarts.com/2011/aa100999.htm
Posted by: marshallzekere.blogspot.com
0 Response to "What Size Warping Board Do I Need"
Post a Comment